Top 9 H-Bridge Motor Controller – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. DAOKI

#ad

DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
DAOKI #ad - Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. The connecting method is shown inbelow figure after enable ENA ENB. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. The signal is shown in the figure. Package included - 5 pcs L298N Motor Driver Controller Board Modules.
BrandDAOKI #ad
ManufacturerDAOKI #ad
Part NumberFBA_TS-US-078-SNL
ModelFBA_TS-US-078-SNL

2. KeeYees

#ad

KeeYees L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with DC Motor and Smart Car Wheel Compatible with Arduino

#ad
KeeYees #ad - Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber. Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability.

It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage. It has the strong driving ability, low calorific value and strong anti-interference ability. Motor drive controller: l298n used as the main driver chip. This is a good parts kit for an arduino and raspberry pi based RC car project.
BrandKeeYees #ad
ManufacturerKeeYees #ad

3. TIMESETL

#ad

TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects

#ad
TIMESETL #ad - Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.

High quality main driver chip l298n, low calorific value, afterflow diode protection, strong driving ability, strong anti-interference, more stable and reliable for Arduino projects. This l298n board comes ready to go. High efficient double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient. Easy to use no assembly required. Just wire up motors and power, easy to use. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge.
BrandTIMESETL #ad
ManufacturerTIMESETL #ad
Height1.18 Inches
Length5.91 Inches
Width3.15 Inches
Part NumberTXJ-061-EU
ModelL298N motor controller

4. Generic

#ad

Smart Car Robot, 2Pack L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Compatible with Ar-duino Electric Projects

#ad
Generic #ad - High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel h-bridge driver working mode creates higher working efficiency, Can drive one 2-phase stepper motor, L298N as main chip, one 4-phase stepper motor or two DC motors. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
BrandGeneric #ad
ManufacturerDoes Not Apply #ad
Part NumberNA
ModelNA

5. ACEIRMC

#ad

Organizer 5pcs L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Controller Board

#ad
ACEIRMC #ad - 3. Great for for arduino diy smart car robot power uno mega r3 mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits. 4.

No assembly required. 5. This l298n board comes ready to go. 2. The chip manual proposes to support 35v, but according to the book When the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, for example, the motor with a rated voltage of 18V shall be driven. Just wire up motors and power, easy to use. 1. When you are driving voltage above logo for the 12 v input, can make to onboard power supply 5 v logic, can actually accept input range is 7 to 12 v for 7 v to 12 v, interface of + 5 v The power supply does not input voltage, when using the onboard after 5 v power supply, but can yield 5V voltage for external use.

Double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
BrandACEIRMC #ad
ManufacturerOrganizer #ad
Part Number10544

6. PChero

#ad

Dual H Bridge DC Stepper For Arduino Smart Car Robot, PChero L298N Motor Drive Controller Board Module

#ad
PChero #ad - Power to 25w. Note: to avoid damage, please use an external 5V logic supply when using more than 12V driving voltage. Just wire up motors and power, this thing will work wonders. And it also use large-capacity filter capacitor and diode with freewheeling protection function, so the module has such features as strong driving ability, thereby improve the reliability of module.

Large current can reach 3A MAX and continue current is 2A. High efficiency - dual-channel h-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.

Package included - 1pcs L298N Motor Driver Controller Board Modules. This l298n board comes ready to go. Item size - external size 43*43*27mm / 1. 69*1. 69*1. 06 inch. High quality - use l298n as the main driving chip, strong anti-interference and low calorific value. Drive voltage 5v-35v, high working power to 46v. Easy of use - no assembly required.
BrandPChero #ad
ManufacturerPChero #ad
Part NumberiS017*1

7. ZYAMY

#ad

ZYAMY 3-Pack L298N Module Dual H Bridge DC Stepper Motor Drive Controller Board for Smart Car Robot

#ad
ZYAMY #ad - Logical voltage: 5v, logical current: 0ma-36ma, driving current: 2AMAX single bridge, drive voltage: 5v-35v, Maximum power: 25W.

Module name: dual h bridge motor Drive Module with L298N high voltage, high current motor drive chip. Function: using the l298n chip drive motor, the chip can drive a two-phase stepping motor or four-phase step motor, and can also drive two dc motors. Package: 3 x l298n dual h-bridge DC Stepper Motor Driver Module. Application: the high voltage large current full bridge drive with two H Bridges can be used to drive the inductive load such as dc motor and stepper motor and relay coil.
BrandZYAMY #ad
Part NumberL298N-2XHB-3

8. MELIFE

#ad

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
MELIFE #ad - If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits. External size 43*43*27mm / 1.

69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Just wire up motors and power, easy to use. Main driver chip l298n, low calorific value, strong driving ability, afterflow diode protection, strong anti-interference, more stable and reliable for Arduino projects. This l298n board comes ready to go. Great for arduino diy smart car robot power uno mega r3 mega2560 duemilanove. No assembly required. Double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient.
BrandMELIFE #ad
ManufacturerMELIFE #ad
Part Number15489

9. SUBALIGU

#ad

2PCS L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge Compatible with Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
SUBALIGU #ad - To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

High working power to 35v, large current can reach 3A MAX and continue current is 2A, power to 25w. Large capacity filter capacitance, afterflow protection diode, more stable and reliable. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel h-bridge driver working mode creates higher working efficiency, L298N as main chip. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
BrandSUBALIGU #ad
ManufacturerSUBALIGU #ad
Part NumberLTC1871-MD-001